Is It Difficult To Paint Malamine

Download Article

Download Commodity

Melamine is a synthetic resin made by mixing melamine and formaldehyde, and it is a mutual binder for house or furniture paint. This paint is durable, so information technology is often used to pigment laminate surfaces, such as cabinets or furniture. Information technology is also very commonly used to cover particle board at pre-fabricated or flat-pack furniture shops. Use a sander and clean all of the surfaces before painting the melamine. And so apply primer and melamine pigment to give a kitchen cupboard or an quondam article of furniture a new lease on life!

one
Fix your workspace before you lot brainstorm. Place newspaper, a tarpaulin, or a drop cloth on the floor below your project. Ventilate the surface area past opening all windows, and turning on a fan if possible.^[1]
- If in that location are other objects close past that you cannot move out of the way, also cover these with a drop cloth to protect them
2

Utilize a sander to lightly roughen the surfaces. Attach 150 grit sandpaper to the sander, and sand every expanse that yous are planning to paint. Pay special attention to the edges and any detailing.^[2]

Ad
3
Apply a liquid deglosser equally a quick culling to sanding. Utilise the deglosser with a paintbrush, and exit information technology to soak into the forest for 15 minutes. And then wipe it off with a textile.^[iii]
- Make sure that you lot are working in a well-ventilated area.
- Liquid deglosser takes the shine off surfaces and makes them tedious to set for painting.
4
Wipe away all of the sanding dust with a tack cloth. Clean away all loose wood, coating, and dust particles from your project. Check all of the joints and corners to make certain that you oasis't missed a spot.
- If at that place is a large mess, you can always vacuum or sweep away the dust kickoff earlier using a tack cloth.
5
Clean all of the surfaces with trisodium phosphate (TSP) detergent. Dilute 4 ounces (110 grand) of TSP powder into 2 gallons (7.6 L) of warm water. Use a sponge to wipe down all surfaces with the solution. So use a make clean rag to rinse all of the surfaces with fresh, clean water.
- Ever wear gloves when using TSP to avoid irritating your skin.
Advert

1
Apply primer with a paintbrush over all of the edges and corners. Use a paintbrush to apply a primer that is specifically for melamine. Target all of the areas that you cannot hands reach with a roller.^[4]
- Primers that are specifically for laminate woods are an culling option.
2
Use a roller to employ the primer to the whole projection. Roll the primer in i direction beyond each surface. Ensure that the roller always sounds crinkly and moisture, and if it loses that sound, employ more primer.^[5]
- If you are using a new roller encompass that has fibers, wrap it in masking record before you utilise it. Rip off the masking tape to remove whatsoever loose fibers that would have otherwise been stuck to your project.^{[half dozen]}
iii
Sand the primer once information technology's dry out to remove whatsoever imperfections. Use 220 grit sandpaper to smooth over any drips or other marks acquired by the primer. Wipe over the sanded surfaces with a tack textile again.^[7]
- The instructions that are on the primer will indicate how long information technology will take to dry. This normally takes around four hours.^[8]
4
Add a second coat of primer. Cover the total surface of the kitchen cupboards or furniture once more. Wait for the primer to dry.^[9]
- Yous don't need to sand the surface once again afterward the second coat of primer, unless you notice more bumps or imperfections.
5
Utilize the beginning coat of melamine paint over the primed surfaces. Use a cream roller to evenly glaze all surfaces with pigment. Let the first coat dry for 6-8 hours.^[10]
- If yous prefer to employ a paint brush, brush against the grain first and and so castor with it.^[11]
- Paint practical to melamine takes longer to dry than on wood. This is because melamine isn't as absorbent.
- You lot can buy pigment specifically for melamine surfaces from home improvement stores.
EXPERT TIP

Sam Adams is the owner of Cherry Design + Build, a residential blueprint and construction firm, which has been operating in the Greater Seattle Surface area for over 13 years. A former architect, Sam is now a full-service contractor, specializing in residential remodels and additions.

Sam Adams
Professional person Contractor

Working on a chiffonier? Sam Adams, design firm owner, advises: "Don't pigment it if it's a chiffonier you utilize all the time. In a year or and so, the paint will start chipping off around the handle because you bear upon the door every day. And if you paint a laminate chiffonier, the paint will chip off all over. Painting a chiffonier is similar a Band-Aid. I think it's meliorate to just supervene upon the entire cabinet."
6

Add the 2d glaze of melamine pigment once the first is dry. Use either a foam roller or paintbrush again to apply paint to all of the surfaces. Allow the final coat dry out for 24 hours.^[12]
7
Spray pigment your projection if you prefer a smoother finished surface. Start with the back or inside of whatever doors to cupboards, so that you tin get used to spray painting in that location beginning. Then spray paint your unabridged projection, and permit it dry overnight.^[13]
- Vesture a respirator mask at all times when working with spray paint.
- Check that the spray paint can exist used on melamine surfaces by reading the label before you purchase it.
- Apply a 2nd glaze with spray paint if you need to one time the first coat is dry.
Advertising

Inquire a Question

200 characters left

Include your electronic mail accost to get a message when this question is answered.

Submit

Advertising

Video

E'er follow all condom instructions that come with your home comeback supplies.

Things Yous'll Need

Newspaper, tarpaulin, or drop material
Sander
Sandpaper
Liquid deglosser
Cleaning fabric
Tack cloth
TSP
Gloves
Primer
Paint brushes
Rollers
Melamine paint

About This Article

Article Summary X

To paint melamine, you'll demand primer designed specifically for melamine or laminate wood as well as some melamine pigment. To get started, crude upwards the melamine with 150-grit sandpaper and then the primer and paint sticks to it better. You tin apply a liquid deglosser to the melamine for 15 minutes instead if you lot're in a rush. Next, apply two coats of primer, letting it dry out after each glaze. Finally, apply 2 coats of melamine pigment using a paintbrush or spray canister and then let everything dry out for 24 hours. To learn how to clean melamine before painting information technology, read on!

Did this summary assist you?

Thanks to all authors for creating a page that has been read 514,442 times.